| Availability: | |
|---|---|
din3055
One image shows the rope wound in multiple layers on a wooden reel with circular flanges. The exact reel dimensions, capacity, wood treatment and export suitability are not provided.
The rope is arranged in repeated layers around the reel barrel. Correct winding quality should be evaluated against the ordered rope diameter, length and handling method.
Another image shows the rope in a loose coil. This confirms flexibility at the pictured scale but does not provide a minimum bend radius or fatigue rating.
The rope is visibly constructed from several twisted strands rather than a single wire or solid bar.
Supply item | Available information |
|---|---|
Product | Steel Wire Rope |
Packaging shown | Wooden reel and loose coil |
Surface appearance | Silver-grey metallic |
Sample display reading | Approximately 8.08 mm |
Nominal diameter | 2~20mm |
Length per reel | 1000m |
Reel dimensions | Not provided |
Net and gross weight | 210kgs |
Rope construction | 6×7+FC |
Material grade | galvanized carbon steel |
Surface treatment | galvanized |
Lubrication | protective and friction-reducing lubricant every 4 months |
Standard | din3055 |
A complete B2B order should define:
rope length per reel;
number of reels;
allowable length tolerance;
reel barrel diameter;
reel flange diameter;
reel width;
arbor or shaft-hole size;
maximum reel weight;
reel material;
export wood-treatment requirement;
moisture protection;
protective wrapping;
end securing method;
reel labels and markings;
palletization;
lifting points for reel handling;
container-loading restrictions.
The images confirm only that a wooden reel is one visible supply form.
Check the reel for broken flanges, loose fasteners, water damage, impact marks and displaced rope layers. Verify labels against the purchase order before removing packaging.
Store the reel in a stable position and protect the rope from contamination, standing water and mechanical damage. Environmental requirements depend on the actual steel grade, coating and lubrication, which are not confirmed.
Use handling equipment suitable for the reel mass and geometry. Do not lift or drag the reel by pulling on the rope end unless an approved procedure allows it.
Mount the reel so that it can rotate under control while the rope is paid off. Avoid pulling turns over a stationary flange, because uncontrolled pay-off can introduce loops, twists or kinks.
Before paying out the rope:
confirm the reel and rope identification;
verify the rope construction and lay;
check the required installation direction;
inspect the accessible outer layers;
confirm compatible handling and tensioning equipment;
prepare the drum, sheaves, guides and termination components;
define the required pre-tension, if any;
establish a safe exclusion zone;
record initial rope condition;
follow the approved equipment procedure.
No installation tension, drum geometry or sheave ratio is provided in the available information.
The supplied photographs include cut ends, but no factory end preparation is shown. Before cutting a multi-strand wire rope, the installation specification should define how the rope is to be seized or secured to prevent strand opening.
The following must be confirmed:
cutting method;
number and location of seizings;
cut-end treatment;
permitted strand disturbance;
termination type;
inspection after termination;
disposal of sharp wire ends.
Do not infer a cutting procedure from the photographs alone.
The product name identifies the material generically as steel. The bright metallic appearance does not identify:
carbon steel versus stainless steel;
zinc coating or another metallic finish;
coating mass or thickness;
lubricant type;
corrosion-resistance level;
tensile grade.
These items must be written into the RFQ and supported by documents when required.
The images do not identify the final application. Reel-supplied steel wire rope may be processed or installed in many different systems, but this product must not be described as suitable for a specific system without confirmed construction and performance.
The buyer should provide:
equipment type;
rope duty;
load spectrum;
speed and bending frequency;
drum and sheave details;
environmental exposure;
termination method;
inspection requirements;
design and regulatory standard.
reel identification and condition;
supplied length and weight;
rope diameter using the specified method;
external strand condition;
kinks, flattening or crushing;
corrosion or staining;
broken or displaced wires;
consistency of winding;
construction against the approved sample;
material and surface documents;
breaking-force certificate, if ordered;
end protection and labels.
A wooden reel is shown in the supplied image. The final packaging format and reel specification require confirmation.
The images do not provide reel length or weight.
A controlled rotating pay-off method should be defined to avoid introducing twists or kinks. The exact procedure depends on the installation plan.
Lubrication is not visible or confirmed.
The display reads approximately 8.08 mm, but the nominal size and measurement tolerance are not established.
No wood treatment, fumigation status or export-packaging certificate is shown.
Provide the rope specification, nominal diameter, length per reel, total quantity, reel limits, packaging, export requirements, delivery destination, documents and intended installation method.
