| Availability: | |
|---|---|
din3055
The digital display in the measurement image reads approximately 8.08 mm. The caliper jaws appear to contact the outside of the rope. However, the photograph does not establish:
calibration status of the caliper;
measurement uncertainty;
specified contact pressure;
exact orientation across strand crowns;
number of measurements taken;
ovality;
nominal size;
permitted tolerance;
test standard;
environmental measurement conditions.
Accordingly, “8.08 mm observed reading” is accurate; “8 mm nominal wire rope” requires separate confirmation.
A dimensional inspection plan should define:
the applicable standard or buyer procedure;
measuring equipment and calibration;
points along the rope to be measured;
orientation of each measurement;
number of readings;
measuring pressure;
treatment of maximum and minimum results;
ovality calculation, if required;
acceptance tolerance;
recording and traceability requirements.
Specification | Status |
|---|---|
Product | Steel Wire Rope |
Construction form | Multiple wires arranged into multiple laid strands |
Surface appearance | Silver-grey metallic |
Core area | Fibrous-looking material visible; exact type unknown |
Packaging | Wooden reel shown |
Observed caliper display | Approximately 8.08 mm |
nominal rope diameter;
diameter tolerance;
required ovality limit;
total length;
length tolerance;
mass per unit length, if controlled;
reel dimensions and maximum weight.
strand count and wire arrangement;
core type;
lay direction;
lay classification;
lay length requirement;
compacted or non-compacted construction;
rotation characteristics;
lubrication condition.
steel type and grade;
wire tensile designation;
surface treatment;
coating type and mass/thickness;
corrosion requirement;
lubricant specification;
restricted-substance requirements.
minimum breaking force;
proof or test requirement;
fatigue or bending requirement, if applicable;
design factor defined by the buyer’s system;
elongation requirement;
application-specific qualification.
material certificate;
dimensional report;
construction certificate;
breaking-force test report;
coating or corrosion report;
length and weight statement;
lot or reel traceability;
inspection certificate;
packaging list.
Only the generic steel identity is provided. The product’s metallic colour cannot distinguish among galvanized carbon steel, bright steel, stainless steel or other finishes.
For an accurate quotation, avoid vague wording such as “silver wire rope.” Specify the required steel grade, coating or uncoated condition, lubricant, environmental exposure and documentation.
Although no finished termination is shown, installation details affect rope selection. Buyers should identify:
drum and sheave dimensions;
bending direction and frequency;
reeving arrangement;
termination type;
load type;
travel speed;
operating environment;
inspection frequency;
replacement policy;
regulatory framework.
Without this information, a supplier cannot reliably confirm application suitability from diameter alone.
obtain the supplier drawing and data sheet;
verify construction from the cut end;
measure diameter using the agreed method;
inspect surface and wire condition;
confirm core type;
verify length and reel packaging;
review material and test certificates;
perform required breaking-force or other tests;
trial the rope in the actual system where appropriate;
approve and retain a reference sample.
ordering by diameter alone;
treating one caliper reading as the nominal specification;
omitting the strand construction;
omitting the core type;
assuming a galvanized finish from colour;
failing to state minimum breaking force;
ignoring drum and sheave conditions;
failing to define rope length and reel limits;
accepting an unspecified test standard;
using a general-purpose description for a safety-critical system.
The photograph shows a digital reading of approximately 8.08 mm on one sample.
No. Nominal diameter and tolerance require a controlled product specification.
The rope is clearly multi-strand, but image perspective and cut-end disturbance make a definitive construction code unreliable.
It appears fibrous, but the exact core type and material cannot be confirmed from the photographs.
No standard is provided. The buyer should state the required national, international, industry or customer standard.
No breaking-force, working-load or tensile-grade data are supplied.
Submit the nominal diameter, tolerance, construction, core, lay, steel grade, finish, minimum breaking force, length, reel, test standard, certificates, quantity and application details.
