| Availability: | |
|---|---|
din3055
multiple small steel wires form individual strands;
several strands are laid together into a rope;
the exterior has a helical pattern;
a fibrous-looking central region is visible in one opened end;
the surface is silver-grey and metallic;
the rope can be coiled and wound onto a reel;
no factory termination is visible.
The exact construction designation, core type and lay must be confirmed before termination design.
An end termination transfers force between the rope and the connected equipment. Its suitability can depend on:
rope diameter;
strand construction;
wire size;
core type;
lay direction;
material and coating;
rope flexibility;
required efficiency;
static or dynamic duty;
environmental exposure;
inspection accessibility;
applicable standard.
A termination selected only by an approximate outside diameter may be unsafe or ineffective.
The buyer or system designer should specify the approved termination method. Possible industry methods exist, but none is confirmed for the pictured rope. The RFQ should therefore identify:
required termination type;
approved fitting material;
fitting dimensions;
installation tooling;
number and position of components;
pressing, socketing or assembly process;
required termination efficiency;
proof test;
inspection method;
marking and traceability.
No clip quantity, swage pressure, socket compound, splice length or assembly torque is provided here.
Multi-strand rope can open or distort when cut if the strands are not controlled. The opened cut-end image illustrates that individual strand bundles can separate after cutting.
Before cutting:
confirm the rope construction and lay;
mark the required finished length;
apply the approved seizing method at the specified positions;
use suitable cutting equipment;
control sharp wire ends;
prevent heat or deformation outside permitted limits;
inspect the end before termination;
preserve identification and traceability.
The exact seizing arrangement and cutting method must come from the approved procedure.
mount the reel securely on a suitable shaft or stand;
control reel rotation during pay-off;
keep the rope aligned with the travel path;
avoid pulling loops over a stationary reel flange;
prevent kinks, birdcaging, crushing and uncontrolled twist;
do not drag the rope over abrasive or contaminated surfaces;
follow the specified reeving direction;
maintain suitable tension during installation where required;
inspect the complete installed length;
document the baseline condition.
Specific pre-tension, fleet angle, drum groove, sheave diameter and reeving instructions are not provided.
The product is identified only as steel wire rope. Its silver-grey appearance does not prove a particular grade or finish.
Before choosing a termination, confirm:
carbon or stainless steel;
galvanized, bright or other finish;
coating dimensions;
lubricant condition;
compatibility between rope and fitting;
galvanic and environmental considerations;
temperature limits;
material certificates.
The photographs do not identify the product as a certified lifting rope, hoist rope, crane rope, elevator rope, guy rope, control cable or sling component. No such use is claimed.
For any load-bearing or safety-related application, the responsible engineer must verify:
complete rope specification;
minimum breaking force;
applicable design factor;
termination efficiency;
equipment compatibility;
proof and acceptance testing;
inspection frequency;
discard criteria;
regulatory compliance;
installation personnel competence.
Check for:
correct product and reel identification;
dimensional compliance;
broken or protruding wires;
flattened or crushed areas;
kinks or loops pulled tight;
disturbed strands;
corrosion, staining or contamination;
heat damage;
insufficient or excessive lubricant, if lubrication is specified;
damage at the cut end;
termination defects;
missing certificates or traceability.
Acceptance criteria must be defined by the applicable specification.
Data item | Status |
|---|---|
Product | Steel Wire Rope |
Construction | Multi-wire and multi-strand, exact code unknown |
Core | Fibrous-looking central material visible; type unknown |
Surface | Silver-grey metallic; treatment unknown |
Sample reading | Approximately 8.08 mm |
No clip type or installation pattern can be recommended without the rope specification, diameter, duty and governing standard.
The opened end shows separated strands. An approved seizing and cutting method should be established before cutting.
No lifting certification, rated capacity or termination is shown. Lifting suitability cannot be assumed.
Compatibility depends on the confirmed rope construction, diameter, material, finish and intended service.
It is only the displayed reading on one sample. Use the confirmed nominal rope specification for fitting selection.
Provide the rope construction, nominal diameter, core, steel grade, finish, duty, minimum breaking force, termination type, proof-test requirement, total length, reel format and governing standard.
