| Availability: | |
|---|---|
din9150
Weifeng/Oem
din9150
central internal thread for a compatible bolt or stud;
hexagonal drive section for installation;
narrowed shear zone designed for controlled separation;
tapered or rounded residual body intended to restrict ordinary tool access.
The exact dimensions and fracture geometry require a controlled drawing.
Define the required material family and exact grade. Potential commercial categories exist, but no target grade is confirmed.
The selection should consider:
required mechanical behaviour;
shear-zone consistency;
mating-fastener material;
indoor or outdoor exposure;
corrosion environment;
temperature;
expected service life;
restricted substances;
traceability and certification.
Hardness, heat treatment and forming condition can influence both thread performance and breakaway response. These values must be specified or approved through supplier documentation and sample testing.
The nut should be reviewed together with the bolt or stud, washer and clamped parts. Dissimilar materials may affect corrosion and thread behaviour.
No surface treatment is confirmed. An RFQ may need to specify:
uncoated condition;
zinc-based coating;
galvanized finish;
stainless-steel natural finish;
passivation;
another project-approved coating;
coating thickness or mass;
colour;
topcoat or sealer;
lubrication;
corrosion-test method and duration;
appearance criteria.
The use of these terms in this section does not claim availability or compliance; they are specification fields for buyer confirmation.
Surface treatment can change friction at:
nut and mating thread;
nut bearing face and joint surface;
installation tool contact.
Changes in friction may alter the relationship between applied torque, joint seating and drive-section breakaway. If the finish changes, the installation process and shear range may require revalidation.
Before choosing a material/finish combination, identify:
indoor, outdoor or sheltered exposure;
moisture and condensation;
salt or coastal exposure;
industrial pollutants;
contact with cleaning chemicals;
contact with treated timber or concrete;
galvanic contact with other metals;
expected maintenance interval;
required corrosion test;
acceptable appearance after exposure.
No corrosion class or test result is available for the target product.
Material and finish should be matched to the confirmed project, which may include security fixtures such as:
fencing systems;
gates and barriers;
signage;
access-control hardware;
public-area installations;
protective equipment covers;
outdoor or indoor utility assemblies.
These are product-category examples, not approvals for the target item.
verify material and finish against the order;
confirm thread compatibility with the mating fastener;
inspect the coating and threads for damage;
start the nut by hand;
tighten the hexagonal drive section with the approved tool;
continue under the validated process until the drive section separates;
inspect the residual body and joint;
protect damaged surfaces only by an approved repair procedure.
No torque value is supplied.
| Requirement | Buyer input needed |
|---|---|
| Base material | Exact grade or approved specification |
| Material condition | Hardness/heat treatment where applicable |
| Surface treatment | Exact coating or natural finish |
| Coating thickness/mass | Required value and method |
| Passivation/topcoat | Required type |
| Lubrication | Type and permitted range |
| Corrosion test | Method and acceptance criteria |
| Colour/appearance | Required limit |
| Mating fastener | Material and finish |
| Shear range | Required value and test method |
| Certificates | Material and finish documentation |
The DIN 9150 designation is supported by a commercial listing, but no official standard document or revision was supplied for this task. The purchase order should reference:
required DIN 9150 edition or supplier drawing;
thread system and tolerance;
full dimensions;
material and finish;
breakaway criteria;
test and inspection methods.
material identification;
hardness or condition verification where specified;
coating measurement;
appearance inspection;
thread gauging before coating and/or after coating as required;
corrosion testing;
sample breakaway testing;
fracture-location inspection;
lot traceability;
certificate review.
No such conclusion can be made. Commercial shear nuts are offered in different materials and finishes.
The target finish is not provided and must be confirmed.
It should not be assumed. Finish and lubrication can affect friction and installation behaviour.
A commercial DIN 9150 listing references A2, but target-product availability and specification require quotation confirmation.
No test method or result is supplied.
Provide the thread, material grade, finish, coating requirement, mating fastener, environment, corrosion test, required breakaway condition, quantity and certificates.
